Note: This page uses the H2D machine as an example. The replacement steps are exactly the same for the H2S, and H2C.

Automatic Top Vent

The automatic top vent is installed on the upper frame of the printer and controls the closing of the vent through a motor.

The spare parts of the automatic top vent include the following:

  1. Automatic top vent*1

  2. Swing rod*1

When to use

  • Automatic top vent is broken

  • Swing rod is broken

Tools and materials needed

  • New automatic top vent

  • H1.5 Allen key

The screw specifications and quantities involved in replacing the H2D automatic top vent kit (it is recommended to properly store the removed screws to prevent loss).

Screw specifications Screw image Location Location diagram Screw quantity
BT2×12 Used to fix the front cover 1

Aviso de Segurança

IMPORTANT!

It’s crucial to power off the printer before conducting any maintenance work, including work on the printer’s electronics and tool head wires. Performing tasks with the printer on can result in a short circuit, leading to electronic damage and safety hazards.

During maintenance or troubleshooting, you may need to disassemble parts, including the hotend. This exposes wires and electrical components that could short circuit if they contact each other, other metal, or electronic components while the printer is still on. This can result in damage to the printer’s electronics and additional issues.

Therefore, it’s crucial to turn off the printer and disconnect it from the power source before conducting any maintenance. This prevents short circuits or damage to the printer’s electronics, ensuring safe and effective maintenance. For any concerns or questions about following this guide, we recommend submitting a chamado técnico relatando o seu problema. and we will do our best to respond promptly and provide the assistance you need.

Remove the automatic top vent

Passo 1: Remove the front cover

Just remove the screen and front cover together. No need to remove the screen from the front cover.

  1. Use an H1.5 Allen key to remove a fixing screw (BT2×12), then hold the buckle on the left side of the front cover with your hand, snap off the top left side of the front cover, and then snap open the top right side:

  1. Then place your thumbs on the bottom of the front cover and push upwards to unlock the front cover card. Then hold the right side of the front cover to bend it slightly and pull the right side of the front cover out from under the right side panel.

Please pull it out carefully to avoid damaging the screen cable!

  1. After pulling the right side of the front cover out of the printer, carefully flip the front cover from right to left to expose the interface between the screen and the screen cable, buckle the screen cable upwards to open the buckle, and then remove the screen cable from the buckle.

Passo 2: Remove the automatic top vent

The automatic top vent is buckled on the upper frame by 4 buckles and connected to the motor through a swing rod.

  1. You can first pry open the buckle on the far right with an Allen key, then use an Allen key to pry open the buckle on the far left, then remove the 2 middle buckles inwards one by one, and finally remove the buckle on the far right facing outwards.

If the swing rod is damaged during replacement, a spare swing rod can be used.

  1. After removing the buckle, you can move the automatic top vent to the left to remove the swing rod from the automatic top vent.

Passo 3: Remove the Vent Motor Base (Optional)

The vent motor base is the support bracket that secures the top automatic vent motor. If the base is damaged, deformed, or not securely installed, it may need to be replaced.

First, remove the motor protective cover from the top.

1_compressed.png

Remove the 3 fixing screws from the motor base: 1 on the top and 2 on the front.

Locate the 2 screws securing the motor to the base and remove them. Carefully separate the motor from the base, avoiding any strain on the connecting cables.

Install the automatic top vent

Passo 1: Install the Vent Motor Base (Optional)

Align the motor with the mounting holes of the new vent motor base and secure it with 2 screws. Tighten them with an H1.5 hex wrench.

Install the assembled motor and base into the original position on the printer. First, tighten the 2 front screws, then tighten the 1 screw on the top.

1_compressed.png

Attach the motor protective cover to the corresponding position, ensuring it is properly aligned.

Passo 2: Install the automatic top vent onto the upper frame

  1. Insert the new swing rod into the automatic top vent first, then hold the automatic top vent, align the swing rod with the motor shaft, and use the Allen key to help push the swing rod into the motor shaft;

  1. First, press down the 2 buckles in the middle of the automatic top vent and buckle them into the buckles. Then press down the 2 buckles on the left and right sides in turn and buckle them into the upper frame.

Passo 3: Install the front cover

  1. First, move the left side of the front cover closer to the left side of the printer, insert the screen cable into the plug, and then fasten the black buckle;

  1. Then hold the right side of the front cover and bend it slightly, insert the right side of the front cover into the printer, and then press the front cover down to make sure all the buckles are in place.

  1. Finally, use a H1.5 Allen key to tighten a fixing screw (BT2x12).

Verify the functionality

Check that all the clips and swing rods of the automatic top vent are in place and can control the opening and closing of the vent normally.

Notas Finais

Esperamos que o guia detalhado fornecido tenha sido útil e informativo.

If this guide does not solve your problem, please submit a chamado técnico, we will answer your questions and provide assistance.

If you have any suggestions or feedback on this Wiki, please leave a message in the comment area. Thank you for your support and attention!