Cable Chain

🔎 Find the P2S Cable Chain in the Bambu Lab store.

The cable chain is a mechanical component connected between the toolhead and the rear of the printer, used to organize and protect the toolhead cables and PTFE tubes.

fac159.jpg

When to Use This Guide

  • The cable chain is cracked or broken
  • The base of the cable chain is damaged and cannot be secured

Required Tools and Materials

  • New Cable chain assembly

Aviso de Segurança

IMPORTANT!

Always power off and disconnect power on the printer before performing maintenance work. Not doing so means there is a risk of electric shock, short circuit, and damage to the printer or surrounding area.

When a maintenance task necessitates the printer being powered on, use insulated gloves for safety and pay special care not to pinch, damage, or put pressure on any exposed wires, connectors, or circuit boards. Additionally, the nozzle can be extremely hot so never touch it with exposed skin.

If you have any questions or concerns related to the above or the steps in this guide, please open a new ticket in our Support Page for assistance.

Remove the Cable Chain

Passo 1: Remove the Toolhead Front Cover

To facilitate removal of the PTFE tube, first remove the toolhead front cover (you do not need to disconnect the wiring).

remove_the_front_housing001.jpg

Passo 2: Remove the PTFE Tube

Press the button on the pneumatic connector of the extruder cover to release the PTFE tube. Then you may close the toolhead front cover.

remove_the_ptfe_tube002.jpg

Next, pull the PTFE tube out of the cable chain clip.

pull_out_the_ptfe_tube003.jpg

Passo 3: Remove the Chain Clips

Unfasten the clips installed on the cable chain and remove them from the chain.

remove_the_chain_clip004.jpg

Passo 4: Remove the Cable Chain

Disconnect the cable chain from its base.

disconnect_the_chain005.jpg

Remove the USB-C data cable from inside the chain.

release_the_usbc_cable006.jpg

Separate the segment of chain connected to the AP board cover (retain two sections on the AP board cover).

disconnect_the_chain007.jpg


Install the Cable Chain

Passo 1: Install the Cable Chain

Position the closed side of the cable chain facing outward, then connect the chain to the AP board cover’s trailing section.

install_the_chain008.jpg

Insert the USB-C data cable (and MC-TH cable) into the chain.

install_the_usbc_cable009.jpg

Attach the chain to its base.

install_the_chain010.jpg

Passo 2: Install the Chain Clips

Attach the chain clips at the 12th section of the cable chain (counting from the toolhead side).

install_the_chain_clip011.jpg

Passo 3: Reinstall the PTFE Tube

Insert the PTFE tube through the clip holes, and reconnect it to the extruder pneumatic fitting.

install_the_ptfe_tube012.jpg


Removing the Cable Chain Base

Passo 1: Disconnect the Cable Chain

Detach the chain from its base bracket, partially remove the USB-C and MC-TH cables to facilitate base removal.

disconnect_the_chain005.jpg

Passo 2: Remove the Base Bracket

Pull out the base bracket, removing it from around the USB-C cable.

cablechain.jpg


Installing the Cable Chain Base

Passo 1: Wire Routing

Lay the USB-C cable into the notch in the cable chain base.

install_the_cable014.jpg

Passo 2: Install the Base Bracket

Mount the base bracket in place with the opening facing right, and secure the USB-C cable properly.

install_the_chain_base015.jpg

Passo 3: Reattach the Cable Chain

Mount the cable chain back onto the base.

install_the_chain010.jpg


Verifying Success

Check that the toolhead cables and PTFE tubing do not protrude outside the chain, and that the toolhead moves normally.

Notas Finais

We hope this guide has provided clear and practical support.
If the issue remains unresolved, please submit a support ticket and include your recent printer logs and additional pictures or other details. Our technical team will review your request and provide detailed assistance.
You can also visit Bambu AI, which can instantly answer common questions and provide you with operational guidance.