Note: This page uses the H2D machine as an example. The replacement steps are exactly the same for the H2S and H2C.

Power Socket

The power socket is a module installed in the lower-left corner of the back of the H2D printer. It includes a power socket, a switch to control the printer’s power, and cables to connect the printer’s power supply, AC board, and ground wire.

The spare parts for the power socket include the following:

  1. Power socket *1

  2. Screw *1 (used to fix the power switch)

  3. Screw *1 (used to fix the ground wire)

When to Use

  • The switch is damaged

  • The connector cables are damaged

  • Poor contact in the socket

Tools and Materials Needed

  • New power socket

  • H2.0 Allen key

Specifications and quantities of screws involved in replacing the H2D power socket (it is recommended to keep the removed screws properly to avoid loss):

Specification Image Use Position Quantity
BT3x8 Fix the rear panel (marked by the green square) 12
Fix the purge chute 1
Fix the power socket 1
Fix the AC board cover 1
ST3x8 Fix the rear panel (marked by the red circle) 11
Fix the power socket 1
ST3x12 Fix the spool holder bracket (marked by the yellow square) 2
BT3x12 Fix the cable clip 2
STW3x5 Fix the ground wire (marked by the red circle) 1

Aviso de Segurança

IMPORTANT!

It’s crucial to power off the printer before conducting any maintenance work, including work on the printer’s electronics and tool head wires. Performing tasks with the printer on can result in a short circuit, leading to electronic damage and safety hazards.

During maintenance or troubleshooting, you may need to disassemble parts, including the hotend. This exposes wires and electrical components that could short circuit if they contact each other, other metal, or electronic components while the printer is still on. This can result in damage to the printer’s electronics and additional issues.

Therefore, it’s crucial to turn off the printer and disconnect it from the power source before conducting any maintenance. This prevents short circuits or damage to the printer’s electronics, ensuring safe and effective maintenance. For any concerns or questions about following this guide, we recommend submitting a chamado técnico relatando o seu problema. and we will do our best to respond promptly and provide the assistance you need.

Remove the Power Socket

Passo 1: Remove the rear panel/purge chute/AC board cover

You can refer to this Wiki to remove the following in sequence:

  1. Rear panel

  2. Purge chute

  3. AC board cover

Since replacing the power socket does not involve disassembling the AC board, you can ignore the steps related to replacing the AC board.

Remove the AC Board and AC Board Cover

Passo 2: Remove the Power socket

  1. Lift the protective cover of the power cable, then use a cross-head screwdriver to loosen the screws and pull the 3 power cables downward.

  • Use an H2.0 Allen key to loosen the 2 fixing screws (BT3x12) for the cable clip. Open the cable clip in the left inner lining and remove the power socket cable from the clip.

  • Use an H2.0 Allen key to loosen the 2 fixing screws for the power socket (red square: ST3x8; green circle: BT3x8). Tilt the power socket and pull it out of the inner lining, then press the clip to disconnect it from the power safety key base.

  • Lift the transparent protective cover below the power supply. Use a cross-head screwdriver to loosen the 3 screws shown in the image, pull the cables downward, and use an H2.0 Allen key to loosen one ground wire screw (STW3x5). Finally, remove the cables from the clip.

Install the Power Socket

Passo 1: Install the power socket

  1. Reconnect the power socket to the power safety key base. Tilt the power socket and insert it (the screw hole on the left should be inserted behind the post). Use an H2.0 Allen key to tighten the 2 fixing screws (red square: ST3x8; green circle: BT3x8).

  • Arrange the cables properly and insert them into the clips in the inner lining. Connect the power socket cable to the power supply, tighten the screws with a cross-head screwdriver, and secure the protective cover. Then, use an H2.0 Allen key to tighten one ground wire screw (STW3x5).

  • Secure the power socket cable under the clip and tighten the 2 fixing screws (BT3x12) for the cable clip inside the left inner lining. Finally, connect it to the AC board, tighten the screws with a cross-head screwdriver, and secure the protective cover.

Passo 2: Install the AC board cover/purge chute/rear panel

You can refer to the following Wiki to install in sequence:

  1. AC board cover

  2. Purge chute

  3. Rear panel

Remove the AC Board and AC Board Cover

Verify the Functionality

Turn on the printer and check if it powers on normally.

Notas Finais

Esperamos que o guia detalhado fornecido tenha sido útil e informativo.

If this guide does not solve your problem, please submit a chamado técnico, we will answer your questions and provide assistance.
If you have any suggestions or feedback on this Wiki, please leave a message in the comment area. Thank you for your support and attention!