Introduction to TimeLapse for H2D/H2D Pro/H2C/X2D
Bambu Lab H2D • Série Comercial H2
Introduction to TimeLapse for H2D/H2D Pro/H2C/X2D
¶ What is Time-Lapse?
If time-lapse photography is enabled during printing, the camera will take a snapshot after each layer is printed, and once the print job is complete, all snapshots will be compiled into a time-lapse video.
¶ Time-Lapse Modes
The two nozzles of a dual-nozzle printer have a height difference of approximately 5mm. When switching nozzles, the heatbed will correspondingly rise/fall by 5mm.

Therefore, during each time-lapse photo capture, if the nozzle in use is inconsistent, the height of the heatbed will also be inconsistent, causing the heatbed in the time-lapse video to jump up and down. As shown below, when using the left and right nozzles to print two cubes of different colors layer by layer, the time-lapse captures a photo at the end of each layer. If the nozzle used at the moment of capture is inconsistent, the position of the heatbed will also jump up and down.

Therefore, to successfully shoot a time-lapse video, the dual-nozzle printer will switch the heatbed to the height corresponding to the same nozzle during time-lapse capture, and minimize unnecessary nozzle switching as much as possible. Depending on the switching strategy, time-lapse photography can be divided into Traditional Mode and Smooth Mode.
¶ Traditional Mode
In Traditional Mode, the printer takes a snapshot directly after each layer is printed. The following is a time-lapse of a dual-nozzle printer using a single nozzle for printing.

¶ Smooth Mode
In Smooth Mode, the nozzle moves away from the model before capturing the time-lapse photo.
- When the print height is less than 5mm, to avoid the heatbed moving and colliding with the nozzle, the nozzle will actively return to the purge wiper area;
- When the print height is greater than 5mm, the nozzle will move to a safe area near the model and wait for the time-lapse capture to complete.

¶ Capture Logic
The main logics for a dual-nozzle printer to shoot time-lapse videos are:
- Calculate the most commonly used nozzle (defined as the “main nozzle“) for each print object by object and layer. For example, the right square printed with gray filament in the image below. Each time the time-lapse takes a snapshot, check whether the current nozzle is consistent with the “main nozzle.” If not, the toolhead will be moved to the purge chute, and the heatbed height will be adjusted to the corresponding height of the “main nozzle” before taking the snapshot.

- The time of taking snapshots should be separated from the time of changing layers. If the “main nozzle” is used for printing on this layer, the time of taking snapshots should be unified to when the “main nozzle” is being used.
Here are some examples for several actual printing scenarios based on the above logic:
- If only one nozzle is used for printing, in Smooth Mode, the photo will also be taken within the safe area;
- If the printing uses both left and right nozzles and each layer uses the main nozzle, the two modes of time-lapse photography are the same as the single nozzle of a single-nozzle printer. As shown in the two-color cube printing task below, since the right nozzle is the main nozzle, the time-lapse photography will take snapshots when printing with the right nozzle, rather than at the end of each layer of printing.

- If both nozzles are used for printing but only one nozzle is used for some layers, when printing these layers, the toolhead will be moved to the purge chute and the heatbed height will be adjusted to the corresponding height of the “main nozzle” before taking the snapshot. In Smooth Mode, the video effect is the same as a single-nozzle printer (such as X1), but in Traditional Mode, these layers become “Smooth Mode”, and the entire video is a mixture of Traditional Mode and Smooth Mode.

- For printing by object, the “main nozzle” will be updated when printing each object, and the time-lapse photography of each object will be processed according to the above three situations. For example, in the following GIF, printing two-color columns by object, the Traditional Mode has a similar effect to a single-nozzle printer (such as X1), and there is no need to adjust the heatbed height when taking photos during the printing of each object.

¶ Known Issues
- When taking snapshots, if the nozzle used for printing is inconsistent with the “main nozzle”, currently only the heatbed height will be adjusted, and the toolhead will not switch the nozzle. In the Smooth Mode time-lapse video, you can see the left hotend moving up and down and the toolhead light switching between left and right.

- When the toolhead moves to the purge chute to take snapshots, it will push up the cutter rod, making some noise.
- Some built-in models (such as Benchy) do not have gcode with time-lapse.
¶ External Accessory Support
The MakerWorld Time-Lapse Photography Kit can be connected to the AMS interface, and forwards commands to the camera device via Bluetooth to enable external time-lapse photography.

When the user selects the “Time-Lapse” option when initiating a print, the firmware will automatically send a photo command to the external accessory when executing time-lapse photography. Due to the long chain from the MC sending commands to the camera completing the photo, and the wide variety of camera models on the market, the time from trigger to photo completion fluctuates. Therefore, in Smooth Mode, the MC firmware defaults to a 500ms delay after sending the command before continuing operation. If a longer delay is needed, it can be configured via the M9711 D parameter (unit: ms). The figure below shows an example with the delay time set to 1s:

For more information about the Time-Lapse Photography Kit, please refer to: Time-Lapse Photography Kit User Guide.
¶ How to Enable and View Time-Lapse Photography?
¶ Enable via Printer Screen
When initiating a print from the printer screen, you can choose whether to enable time-lapse photography.

¶ Enable and View via Bambu Studio
In the menu bar of the slicing software, click “Special Mode” under the “Others” option, where you can find “Timelapse”;

Before you start printing, ensure that an SD card with sufficient memory space is inserted into the printer, and check the “Timelapse” option when sending the print job.

Note: When selecting Smooth Mode, ensure that the Prime Tower is enabled (this feature is turned on by default).
After printing is complete, you can directly download the time-lapse video file from the “Device > Storage” page in Bambu Studio.

¶ Enable and View via Bambu Handy
Click “Prepare to Print > Options > Timelapse” to enable time-lapse photography, as shown in the GIF below:

Once the print is complete, you can find the recorded time-lapse video under Device Interface > Timelapse, and choose to download it to your local photo gallery.

¶ Physical Storage Path
If you choose to store the time-lapse files on an external SD card, after printing is complete, you can find the corresponding video files in the timelapse folder on the SD card:

The X2D allows you to choose to save time-lapse files to either external or internal storage. For details, please refer to: Time-Lapse Internal Storage and Video Management.
¶ FAQs
¶ 1. The Relationship Between Time-Lapse Duration and Printing Duration
The duration of the timelapse video is independent of the actual printing time; the time-lapse duration is solely determined by the number of layers and the frame rate.
Consequently, some models with a larger print area but lower layer height may still result in a shorter timelapse video, even if their overall print time is longer.
Total frames = the number of layers (N), frame rate = 30 (fps).
For example: 1000 layers / 30fps → video length ≈ 33.3 seconds.
¶ 2. Dark Preview During the Printing Process
To prevent flickering or inconsistent brightness caused by changes in ambient light, the timelapse process locks the exposure, ensuring consistent brightness throughout the sequence. However, if printing begins in a bright environment, the locked exposure setting will cause the Live View to appear too dark when the ambient light decreases (such as the transition from day to night).
¶ End Notes
We hope our guide was helpful and provided you with clear and practical assistance.
If the issue remains unresolved, please submit a service ticket along with your recent printer logs, as well as relevant photos or other detailed information. Our technical team will be available to answer your questions and provide support.
You can also visit Bambu AI, which can instantly answer common questions and provide you with operational guidance.

