Cold Pull

During 3D printing, ensuring the nozzle is clean and unobstructed is crucial for print success and quality. We strongly recommend performing regular nozzle maintenance to effectively extend its lifespan.

The following are scenarios where you must perform a cold pull maintenance:

  1. Frequent extruder motor errors indicating abnormal resistance: When the extruder motor frequently reports abnormal resistance at regular printing flow rates, it signifies excessive nozzle resistance and requires immediate cleaning.
  2. Before switching to TPU filament: Given that TPU filament is highly sensitive to nozzle resistance, if the nozzle has previously printed other filaments, we recommend performing a cold pull cleaning before printing TPU to ensure smooth printing.

Note: If the nozzle is completely clogged, filament cannot be purged. In this case, refer to Hotend Clog Cleaning Guide first, use the unclogging pin to push the blockage inward, and then perform the cold pull operation.

Safety Tips

Before performing any maintenance on the printer and its electronic components (including the toolhead cable), turn off the printer and disconnect the power supply to prevent accidental screen touches or short circuits, which could cause additional electronic damage and safety hazards.
When performing maintenance or troubleshooting on your printer, please first check the temperature of the hotend and heatbed. Avoid operating at high temperatures. If operating at high temperatures is unavoidable, wear insulated gloves to ensure safe and effective maintenance.

Flowchart

%%{init: {“themeVariables”: {“fontSize”: “11px”}, “themeCSS”: “.edgePath .path, path.flowchart-link { stroke-width: 0.5px; }”}}%%
flowchart TD
A[“Start the Cold Pull”]
B[“Observe Purge”]
C{“Can the filament be extrude?”}
D[“Stop the Cold Pull”]
E[“Set the hotend temperature”]
F[“Clear with unclogging pin”]
I[“Cold Pull Completed”]

A –> B
B –> C
C –>|No| D
C –>|Yes| I
D –> E
E –> F
F –> A

classDef process fill:#D6ECFF,stroke:#4A90E2,stroke-width:1px,color:#000;
classDef decision fill:#fff2cc,stroke:#d6b656,color:#000;

class A,B,D,E,F,I process;
class C decision;

Cold Pull Process

Tap Toolbox.
04_nozzle_cold_pull_guide_for_the_h3c_c118e0042c.png

Select Nozzle Cold Pull.
04_nozzle_cold_pull_guide_for_the_h3c_0b98dce705.png

Tap Next.

04_nozzle_cold_pull_guide_for_the_h3c_8cf78ed29e.png 04_nozzle_cold_pull_guide_for_the_h3c_87efa70671.png

Select the filament and melting temperature, then tap Start.
04_nozzle_cold_pull_guide_for_the_h3c_0bde58649a.png

Start the cold pull after confirming that there are no foreign objects on the heatbed surface, as prompted.
04_nozzle_cold_pull_guide_for_the_h3c_95a2716814.png

Remove the AMS’s magnetic side cover.

03_timing_belt_tensioning_guide_for_the_h3c_edc9260de1.png 03_timing_belt_tensioning_guide_for_the_h3c_d1bd51050d.png

Press the black release tab and remove the filament tube as prompted.

04_nozzle_cold_pull_guide_for_the_h3c_9938110eef.png 04_nozzle_cold_pull_guide_for_the_h3c_77927ecbf2.gif

Insert a filament piece longer than 30cm.
04_nozzle_cold_pull_guide_for_the_h3c_224e9fef71.png

Wait for filament purge.
04_nozzle_cold_pull_guide_for_the_h3c_336507eb21.png

Observe if the hotend can extrude filament. If not, stop the cold pull and use the unclogging pin to clear it a few times. If extrusion is very smooth, you can skip this step.

Please note that this method is not applicable to hotends with a diameter smaller than 0.4mm.
04_nozzle_cold_pull_guide_for_the_h3c_0914bb1a16.webp

Wait for cooling.
04_nozzle_cold_pull_guide_for_the_h3c_b1b99477c7.png

Slowly pull out the filament as prompted.
04_nozzle_cold_pull_guide_for_the_h3c_f9f2a37b85.png

Check the cold pull quality.
04_nozzle_cold_pull_guide_for_the_h3c_efa90d80d0.png

If the end of the filament forms a sharp point, the cold pull was successful.If there are colored impurities in the cold-pulled area, repeat the cold pull until the filament surface is clean.
04_nozzle_cold_pull_guide_for_the_h3c_35e7a8d339.png

Reinsert the filament tube.
04_nozzle_cold_pull_guide_for_the_h3c_29e83f81ec.png

Notas Finais

We hope this guide has provided clear and practical support.
If the issue remains unresolved, please submit a support ticket and include your recent printer logs and additional pictures or other details. Our customer support team will review your request and provide detailed assistance.
You can also visit Bambu AI, which can instantly answer common questions and provide you with operational guidance.