Adaptive Airflow Assembly – Rear

28_rear_adaptive_airflow_assembly_and_rear_chamber_heater_assembly_replacement_guide_for_the_77ff5ccc6d.jpg

Chamber Heater Assembly – Rear

28_rear_adaptive_airflow_assembly_and_rear_chamber_heater_assembly_replacement_guide_for_the_753106bd92.jpg

Applicable Printer Model

Bambu Lab H3C

When to Replace

Adaptive Airflow Assembly – Rear

  • Adaptive Airflow switching failed
  • Control board burnt out or connector damaged
  • HMS prompts an error and it is confirmed by technical support
    Rear Chamber Heater Assembly
  • Chamber Heater Assembly – Rear burnt out
  • HMS prompts an error and it is confirmed by technical support

Safety Tips

Before performing any maintenance on the printer and its electronic components (including the Toolhead Cable), turn off the printer and disconnect the power supply to prevent accidental Screen touches or short circuits, which could cause additional electronic damage and safety hazards.
07_ap_board_replacement_guide_for_the_h3c_01457bbe50.jpg

When performing maintenance or troubleshooting on your printer, please first check the temperature of the hotend and heatbed. Avoid operating at high temperatures. If operating at high temperatures is unavoidable, wear insulated gloves to ensure safe and effective maintenance.

Tools and Materials

  • H2.0 allen key
  • H1.5 Allen Key

Remove the Adaptive Airflow Assembly – Rear

Passo 1. Remove the Rear Panel

Refer to the dedicated Rear Panel Replacement Guide for the H3C, disconnect the power cable, and remove the rear panel.
28_rear_adaptive_airflow_assembly_and_rear_chamber_heater_assembly_replacement_guide_for_the_9284139891.jpg

Passo 2. Disconnect the Cables

Disconnect the 3 cables from the control board located on the bottom left of the air duct, and release the cables from the clips on the surface of the air duct.
28_rear_adaptive_airflow_assembly_and_rear_chamber_heater_assembly_replacement_guide_for_the_ff7a4b32e8.jpg

Passo 3. Remove the Adaptive Airflow Assembly – Rear

Use an H2.0 allen key to remove the 6 screws, and remove the Rear Adaptive Airflow Assembly.
28_rear_adaptive_airflow_assembly_and_rear_chamber_heater_assembly_replacement_guide_for_the_03ea4c8277.png

Install the Adaptive Airflow Assembly – Rear

Passo 1. Install the Adaptive Airflow Assembly – Rear

Install the Adaptive Airflow Assembly – Rear above the rear heating assembly. Ensure the screw holes at the connection point with the rear heating assembly are located beneath the housing of the rear heating assembly.
28_rear_adaptive_airflow_assembly_and_rear_chamber_heater_assembly_replacement_guide_for_the_696266a49f.jpg

Hold the air duct assembly in place to prevent it from falling, then sequentially tighten the 6 screws following the numbered order indicated in the diagram.
28_rear_adaptive_airflow_assembly_and_rear_chamber_heater_assembly_replacement_guide_for_the_fa9decbb0f.jpg

Passo 2. Connect the Cables

Connect the 3 plugs to the control board on the bottom left of the air duct, and secure the cables into the clips on the surface of the air duct.
28_rear_adaptive_airflow_assembly_and_rear_chamber_heater_assembly_replacement_guide_for_the_ff7a4b32e8.jpg

Passo 3. Install the Rear Panel

Refer to the dedicated Rear Panel Replacement Guide for the H3C to install the rear panel and other accessories.
19_ac_board_replacement_guide_for_the_h3c_2980526540.jpg

Remove the Chamber Heater Assembly – Rear

Reminder: The disassembly and assembly of the rear chamber temperature assembly shall be carried out after the air duct assembly is removed.

Disconnect the two power cables for the Chamber Heater Assembly – Rear from the AC board, then route the cables along their path towards the Chamber Heater Assembly.
28_rear_adaptive_airflow_assembly_and_rear_chamber_heater_assembly_replacement_guide_for_the_9c0124626a.jpg

Use an H2.0 allen key to remove the 2 screws, and remove the Rear Chamber Heater Assembly.
28_rear_adaptive_airflow_assembly_and_rear_chamber_heater_assembly_replacement_guide_for_the_d142b53ec9.jpg

Install the Chamber Heater Assembly – Rear

Install the Chamber Heater Assembly at the bottom of the left inner lining. Align the screw holes and secure with 2 screws.
28_rear_adaptive_airflow_assembly_and_rear_chamber_heater_assembly_replacement_guide_for_the_d142b53ec9.jpg

Connect the rear chamber temperature power cable to the quick-connect terminals on the AC board, following the wiring path shown in the diagram.
28_rear_adaptive_airflow_assembly_and_rear_chamber_heater_assembly_replacement_guide_for_the_10d7af9523.jpg

Notas Finais

We hope this guide has provided clear and practical support.
If the issue remains unresolved, please submit a support ticket and include your recent printer logs and additional pictures or other details. Our customer support team will review your request and provide detailed assistance.
You can also visit Bambu AI, which can instantly answer common questions and provide you with operational guidance.