Idler Pulley Replacement Guide for the H3C
Bambu Lab H3C • Série Industrial H3
Idler Pulley Replacement Guide for the H3C
Idler Pulley
The idler pulley assemblies described in this guide refer to the 12 relatively easy-to-replace idler pulleys used in the XY synchronous belt path:
- Idler pulley assemblies installed on both sides of the printer’s rear uprights, 8 in total;
![]() |
![]() |
-
Idler pulley assemblies installed on both sides of the printer’s front uprights, 2 in total;

-
Idler pulley assemblies installed on the left Y carriage, 4 in total (the 2 upper ones are applicable to this guide; the 2 lower ones can only be handled after the X-Axis Assembly is removed). )
![]() |
![]() |
Applicable Printer Model
Bambu Lab H3C
When to Replace
- Idler pulley noise
- The idler pulley is dirty or deformed and cannot be restored.
Tip: Since the replacement of the left and right idler pulleys are operationally similar, this guide will use the left idler pulley as an example.
Safety Tips
Before performing any maintenance on the printer and its electronic components (including the Toolhead Cable), turn off the printer and disconnect the power supply to prevent accidental Screen touches or short circuits, which could cause additional electronic damage and safety hazards.
When performing maintenance or troubleshooting on your printer, please first check the temperature of the hotend and heatbed. Avoid operating at high temperatures. If operating at high temperatures is unavoidable, wear insulated gloves to ensure safe and effective maintenance.
Tools and Materials
- H2.0 allen key
Remove the Idler Pulley Assembly (rear)
Using an H2.0 allen key, remove the 2 screws; gently pull the synchronous belt at the corresponding position to detach the entire idler pulley assembly.
![]() |
![]() |
Install the Idler Pulley Assembly (rear)
Thread the idler pulley shaft through the idler pulley and install it onto the idler pulley bracket. Install the idler pulley assembly into its position, press it by hand, and lock in the 2 screws for fixation.
![]() |
![]() |
Remove the Idler Pulley Assembly (front)
- The 2 idler pulley assemblies at the front are obscured by the SwapTek Rack. If replacement is necessary, please refer to the dedicated SwapTek Rack Replacement Guide for the H3C for removing and installing the SwapTek Rack (after replacing the idler pulley assembly).
- Remove the XY belt fixing bracket on the same side as the idler pulley to be replaced.
Using an H2.0 allen key, remove the 3 screws in the order indicated by the screw markings in the diagram to loosen the XY belt fixing bracket.
![]() |
![]() |
Use an H2.0 allen key to remove the 2 screws and take off the front idler pulley bracket.
![]() |
![]() |
Use a wrench to gently pry the idler pulley and the synchronous belt out of the idler pulley slot, and remove the idler pulley.
![]() |
![]() |
Install the Idler Pulley Assembly (front)
Thread the idler pulley shaft through the idler pulley, position it at the XY synchronous belt turning point, and then place them together into the idler pulley slot.
![]() |
![]() |
Check the orientation of the idler pulley bracket. The side with the higher obstruction should face the front door. Install it into the idler pulley position and lock in 2 screws for fixation.
![]() |
![]() |
Install the XY belt fixing bracket onto the toolhead. Press and hold the fixing bracket with your hand, first tighten the 1 screw in the middle position, and then tighten the 2 upper and lower screws.
![]() |
![]() |
Remove the Idler Pulley Assembly (y Carriage)
Using an H2.0 allen key, remove the 3 screws in the order indicated by the screw markings in the diagram to loosen the XY belt fixing bracket.
![]() |
![]() |
Using an H2.0 allen key, unscrew the idler pulley screw shaft, gently pull the belt, and remove the idler pulley.
![]() |
![]() |
Install Idler Assembly (Y Carriage)
Insert the idler onto the Y carriage, ensuring the XY synchronized belt is pressed back by the idler. Insert the idler screw shaft and manually adjust the idler’s position so that the idler screw shaft can pass completely through the idler and into the threaded hole below. Tighten the screw shaft.
![]() |
![]() |
Install the XY belt fixing bracket onto the toolhead. Press and hold the fixing bracket with your hand, first tighten the 1 screw in the middle position, and then tighten the 2 upper and lower screws.
![]() |
![]() |
Verify Functionality
After replacing the idler, please refer to the dedicated Belt Tension Guide for the H3C and perform an XY belt tensioning operation.
Notas Finais
We hope this guide has provided clear and practical support.
If the issue remains unresolved, please submit a support ticket and include your recent printer logs and additional pictures or other details. Our customer support team will review your request and provide detailed assistance.
You can also visit Bambu AI, which can instantly answer common questions and provide you with operational guidance.






















