E1 Front Cover

img_50e472dba800.png

When to Replace

  1. The screen is damaged or the display is abnormal.
  2. The front cover assembly is damaged or deformed.

Safety Tips

Before performing any maintenance on the air purifier and its electronic components, power off the device and disconnect the power supply to prevent circuit shorts, which can cause additional device damage and safety risks. Before maintenance or troubleshooting, please ensure that the relevant parts have cooled down.

Tools and Materials

  • H2.0 Allen key
  • H1.5 Allen Key

Remove the E1 Front Cover

Passo 1. Remove the Filter Element

Disconnect the air duct connected to the purifier, the Power Cable, and the 6-pin cable (if any).
img_7435483712db.png

Slide the rear cover upwards to remove it.
img_bdecd87a5c1e.webp

Take out the filter element handle, pinch the handle, and pull out the filter element.
img_1b59bdb65368.webp

Passo 2. Separate the Front and Rear Housings

Peel off the three foam strips as shown.

img_ea65db2d1931.webp img_49ec1bf04430.webp
img_c657f36bae53.webp

Turn the device over and remove the footpads from the front housing.
img_01b955ba79af.webp

Use an H2.0 Allen key to remove the two screws.
img_66b355df62d0.png

Use an H2.0 Allen key to remove the seven screws shown.
img_e45d175eeb9c.png

Separate the front and rear housings, then disconnect the connecting cables between them.
img_59943b1ca9ce.webp

Passo 3. Remove the E1 Button Assembly with Chamber Temperature Sensor, Mainboard, and Fan

Disconnect the three connectors shown.

img_4f4304e6da87.png img_9427320d4857.webp

Use an H2.0 Allen key to remove the two screws, then remove the button board with the chamber temperature sensor.
img_647ec66f8a25.png

Use an H1.5 Allen key to remove the single screw and disconnect the Screen ground wire.
img_58f834c45953.png

Use an H1.5 Allen key to remove the remaining three screws, then remove the mainboard.
img_85b7deb85e5b.png

Use an H2.0 Allen key to remove the three screws, then remove the fan.
img_aa37f0aef19f.png

At this point, all other components on the front cover have been completely disassembled. Please refer to the installation steps to reassemble the components onto the new front cover assembly.
img_e1fe4bafe984.png

Install the E1 Front Cover

Passo 1. Install E1 Fan, Mainboard, and Button Board with Chamber Temperature Sensor

Reinstall the fan and secure it with the three screws using an H2.0 Allen key.
img_aa37f0aef19f.png

Reinstall the E1 mainboard and secure the three screws with an H1.5 Allen key.
img_85b7deb85e5b.png

Reinstall the screen ground wire and secure it with one screw using an H1.5 Allen key.
img_58f834c45953.png

Reinstall the button board with the chamber temperature sensor and secure it with the two screws using an H2.0 Allen key.
img_647ec66f8a25.png

Reinstall the fan, Button board with Chamber Temperature Sensor, and the screen connector cable plug.
img_4f4304e6da87.png

Passo 2. Install the Front and Rear Housings

Connect the three plugs as shown, then close the front and rear housings.
img_f2016127d761.png

Use an H2.0 Allen key to secure the seven screws.
img_e45d175eeb9c.png

Turn the device upside down and use an H2.0 Allen key to secure the two screws.
img_66b355df62d0.png

Attach the footpads.
img_78c4f0847459.png

Attach the foam strips around the filter element.
img_22df9218a3d1.png

Passo 3. Install the Filter Element

Install the filter element, ensuring the handle side faces outwards.
img_06d637b9d826.webp

Tuck the filter element handle into the filter mesh to avoid obstructing the rear cover installation.
img_479ed8afeffe.png

Install the rear cover.
img_97c66324855e.webp

Reinstall the purifier air duct, Power Cable, and 6-pin cable (if any).
img_d9e789a11aaf.png

Verifying Functionality

After the replacement is complete, confirm that the front cover is securely installed, the locking tabs are in place, and it fits snugly with the main body without any noticeable gaps. Start the purifier and confirm that it operates normally, with no looseness, abnormal noise, or unusual vibrations coming from the front cover.

Notas Finais

We hope this guide has provided clear and practical support.
If the issue remains unresolved, please submit a support ticket and include your recent printer logs and additional pictures or other details. Our customer support team will review your request and provide detailed assistance.
You can also visit Bambu AI, which can instantly answer common questions and provide you with operational guidance.