Right Side Panel Replacement Guide for the H3C
Bambu Lab H3C • Série Industrial H3
Right Side Panel Replacement Guide for the H3C
Right Panel
The plastic cover installed on the right side of the printer, with a window already installed on the side panel.

Applicable Printer Model
Bambu Lab H3C
When to Replace
Structural damage or scratches on the side panel.
Safety Tips
Before performing any maintenance on the printer and its electronic components (including the Toolhead Cable), turn off the printer and disconnect the power supply to prevent accidental Screen touches or short circuits, which could cause additional electronic damage and safety hazards.
When performing maintenance or troubleshooting on your printer, please first check the temperature of the hotend and heatbed. Avoid operating at high temperatures. If operating at high temperatures is unavoidable, wear insulated gloves to ensure safe and effective maintenance.
Tools and Materials
- H2.0 allen key
Disassembly and Assembly Tips
Disassembly and assembly of the printer’s side panel requires the AMS 3H to be removed beforehand. Please refer to the dedicated AMS 3H Removal and Installation Guide to remove and reinstall the AMS 3H from the printer. All operations in this guide are performed with the AMS 3H removed.
Remove the Right Panel
Passo 1. Lower the Heatbed
Because there are screws inside that lock the side panel, lower the heatbed first to facilitate screw removal.
Turn on the printer, perform an XYZ homing operation, then tap the “Lower Heatbed” icon on the screen to lower the heatbed to the bottom.
Passo 2. Remove the Right Panel Screws
The side panel is secured with numerous screws that need to be removed one by one.
First, remove the 3 screws located at the top. One of these screws is under the foam of the front cover and requires the foam to be destroyed for removal.

Next, remove the 2 screws located under the seal of the front door.

Next, remove the remaining 6 screws on the inside of the printer. 3 of these screws are on the front uprights, and the other 3 secure the chamber temperature component.

Finally, remove the 3 screws on the back of the printer.

Passo 3. Remove the Right Panel
In addition to screws, the side panel is also secured and positioned with several locking tabs. When removing the side panel, pay attention to the force and direction to avoid damaging the tabs.
As shown in the image below, apply force at the position of the front door seal. First, detach the side panel slightly from the printer, then detach the rear side as well.
Then, use a pry tool or wrench to pry from the upper part of the detached side panel, completely disengaging the upper locking tabs from the printer, and then remove the side panel at an upward angle.
![]() |
![]() |
Install the Right Panel
Passo 1. Install the Right Panel
Align the locking tabs on the bottom of the side panel with the mounting slots on the bottom of the printer and install.

If the small locking tab on the handle area is exposed, press it in firmly.

Close the upper part of the side panel. Pay attention to the alignment between the side panel and the front cover. The locking tab is at the bottom. Press the side panel to ensure it fits flush with the printer frame.

Passo 2. Screw in Side Panel
To avoid significant assembly deviations, tighten the screws in the following order.
First, tighten the 3 screws located at the top.

Next, screw in the 6 screws on the inside of the printer. 3 of these screws are on the front uprights, and the other 3 are for the chamber temperature component.

Then, tighten the 3 screws on the back of the printer

Finally, tighten the 2 screws located under the seal of the front door.

Verify Functionality
After installation, check that the side panel is not lifted and all locking tabs are secured to the printer.
Notas Finais
We hope this guide has provided clear and practical support.
If the issue remains unresolved, please submit a support ticket and include your recent printer logs and additional pictures or other details. Our customer support team will review your request and provide detailed assistance.
You can also visit Bambu AI, which can instantly answer common questions and provide you with operational guidance.




