ToolLock Assembly

It consists of a locking pin and a locking spring clip. Driven by the locking motor, it positions and secures the tool, ensuring that the tool remains stable during operation

When to Replace

When structural components are worn and affect product performance.

Tools and Materials

  • H1.5 Allen Key
  • H2.0 Allen key
  • Special Socket

Safety Tips

Before performing any maintenance on the printer and its electronic components (including the Toolhead Cable), turn off the printer and disconnect the power supply to prevent accidental Screen touches or short circuits, which could cause additional electronic damage and safety hazards.
05_side_panel_left_replacement_guide_8c09dac0a4.png

When performing maintenance or troubleshooting on your printer, please first check the temperature of the hotend and heatbed. Avoid operating at high temperatures. If operating at high temperatures is unavoidable, wear insulated gloves to ensure safe and effective maintenance.

Remove the ToolLock Assembly

Passo 1. Remove the Toolhead Front Cover

Refer to the wiki: Toolhead Front Cover Replacement Guide to remove the toolhead front cover.

Passo 2. Loosen the Hotend Fan and Coil Cables

Using the H1.5 Allen key, remove the two screws and slide the hotend fan to the right to release it.

53_toollock_assembly_replacement_guide_86e4ab2c17.png 53_toollock_assembly_replacement_guide_18c9066582.png

Loosen the eddy current coil cable from the clip under the driven wheel and keep it away from the silver screw as much as possible to avoid damage during disassembly.

53_toollock_assembly_replacement_guide_bf62391e77.png 53_toollock_assembly_replacement_guide_383a99eeef.png

Passo 3. Remove the ToolLock Assembly

Use the H1.5 Allen key to remove the silver screw and the H2.0 Allen key to remove the black screw. Then, attach the dedicated socket to the H2.0 Allen key.

53_toollock_assembly_replacement_guide_172d1bc232.png 53_toollock_assembly_replacement_guide_eee153c7ab.png

Turn the ToolLock motor shaft clockwise with the dedicated socket to disengage the locking pin to the left, then pull it out by hand.

53_toollock_assembly_replacement_guide_c3e98eab00.png 53_toollock_assembly_replacement_guide_63a522141f.png

Use an H1.5 Allen key to remove the black screw and remove the ToolLock Spring by hand.

53_toollock_assembly_replacement_guide_013177bc89.png 53_toollock_assembly_replacement_guide_2d12e0fc8e.png

Install the ToolLock Assembly

Passo 1. Install the ToolLock Assembly

Install the ToolLock Spring above the tool positioning slot, then secure it with one black screw (long screw).

53_toollock_assembly_replacement_guide_2d12e0fc8e.png 53_toollock_assembly_replacement_guide_013177bc89.png

Before installing the new locking pin, apply dedicated lubricant grease to the pin. Then, install it into the slot. For more detailed operations, please refer to the wiki: H3C Printer Periodic Maintenance.

53_toollock_assembly_replacement_guide_c36f964dfd.png 53_toollock_assembly_replacement_guide_d663f00a7a.png

Install the locking pin along the pin slot, hold the pin by hand, and then turn the ToolLock motor shaft counterclockwise with the dedicated socket. The locking pin will continue to move to the right.

53_toollock_assembly_replacement_guide_5f4a8cf6b3.png 53_toollock_assembly_replacement_guide_a003bc886f.png

After the screw hole on the left side of the pin is fully exposed, insert the silver screw and the black screw to fully secure the ToolLock Assembly.

53_toollock_assembly_replacement_guide_2c2e304773.png 53_toollock_assembly_replacement_guide_172d1bc232.png

Passo 2. Organize the Cables and Secure the Hotend Fan

Organize the coil cables loosened during disassembly into the clips on the driven wheel. Then, install the hotend fan and secure it with two screws.

53_toollock_assembly_replacement_guide_bf62391e77.png 53_toollock_assembly_replacement_guide_86e4ab2c17.png

Passo 3. Install the Toolhead Front Cover

Refer to the wiki: Toolhead Front Cover Replacement Guide to install the toolhead front cover.
53_toollock_assembly_replacement_guide_af4785e60b.png

Verify Functionality

Connect the power supply, turn on the printer, and perform a PrintTool loading operation. Ensure that the operation completes successfully.

Notas Finais

We hope this guide has provided clear and practical support.
If the issue remains unresolved, please submit a support ticket and include your recent printer logs and additional pictures or other details. Our customer support team will review your request and provide detailed assistance.
You can also visit Bambu AI, which can instantly answer common questions and provide you with operational guidance.