Heatbed Replacement Guide for the P2S
Bambu Lab P2S • Série Performance P2
Heatbed Replacement Guide for the P2S
Heatbed
The heatbed of a printer is a platform installed inside the printer chamber. It moves up and down along the Z-axis and is heated to a set temperature. Setting the appropriate heatbed temperature can effectively improve adhesion between the model and the build plate while helping to prevent warping.

When to Use This Guide
- Heatbed is damaged.
- Bambu Lab technical support has concluded that the heatbed requires replacement.
Tools and Materials Required
- Heatbed * 1
- BT3x8 screw * 7- for fixing the heatbed
- STW3.5×6 screw * 1- for fixing the ground wire
- BT2x5 screws * 4 – for securing the cable clamp
Aviso de Segurança
IMPORTANT!
Always power off and disconnect power on the printer before performing maintenance work. Not doing so means there is a risk of electric shock, short circuit, and damage to the printer or surrounding area.
When a maintenance task necessitates the printer being powered on, use insulated gloves for safety and pay special care not to pinch, damage, or put pressure on any exposed wires, connectors, or circuit boards. Additionally, the nozzle can be extremely hot so never touch it with exposed skin.
If you have any questions or concerns related to the above or the steps in this guide, please open a new ticket in our Support Page for assistance.
Remove the Heatbed
Passo 1: Remove the Rear Panel
You can refer to this wiki to remove the rear panel: Replace the Rear Panel.
Passo 2: Remove the Left Side Panel
You can refer to this wiki to remove the left side panel: Replace the Left Side Panel.
Passo 3: Remove the Purge Chute
Use an H1.5 Allen key to remove the four screws securing the purge chute, then remove it from the printer.

Passo 4: Remove the Heatbed
- First, disconnect the heatbed temperature cable from the MC board.

- Disconnect the heatbed power cables from the AC board. When disconnecting, press the latch on the interface to unlock it, and then unplug the cables.

⚠️ Note: There are two versions of P2S heatbed. The Version 1 heatbed has 3 power cables (red, blue, and gray), so all three cables need to be disconnected; the Version 2 heatbed has only 2 power cables (red and gray), so only these two cables need to be disconnected. Please proceed according to actual configuration.
![]() |
![]() |
|
Version 1: three cables (red, blue, gray)
|
Version 2: two cables (red, gray)
|
- Use a H2.0 Allen key to remove the ground wire fixing screw (STW3.5×6), then detach the ground wire from the frame and the cable clip.
![]() |
![]() |

- Use an H1.5 Allen key to remove the two cable clamp screws (BT2×5) on the power cover, and remove the cable clamp. Then pass the heated bed cable through the cable gland on the power supply protection cover.
![]() |
![]() |
- Use an H1.5 Allen key to remove the two cable clamp fixing screws (BT2x5) on the bottom of the Z slider and remove the cable clamp.

- Use an H2.0 Allen key to remove the seven heatbed fixing screws (BT3x8). Lift the heatbed up and lay it on its side, then unplug the heatbed cable from the Z slider. Finally, remove the heatbed.
![]() |
![]() |

Install the Heatbed
Passo 1: Install the Heatbed
- Place the new heatbed sideways into the printer and thread the cables through the Z slider. To do this, first pass the heatbed power cables through the Z slider and pull them through. Next, thread the ground and temperature cables through the Z slider as well.
⚠️ Note: There are two versions of the P2S heatbed. The Version 1 heatbed has 3 power cables (red, blue, and gray); the Version 2 heatbed has only 2 power cables (red and gray). Please refer to the version you received.
![]() |
![]() |

- Place the heatbed onto the Z sliders. First, use an H2.0 Allen Key to tighten the four screws at the rear of the heatbed (numbered 1–3). Then insert the four screws at the front (numbered 4–7), but do not fully tighten them yet to allow for later adjustment of the heatbed position.
![]() |
![]() |
- Arrange the cables at the bottom of the Z slider into the cable duct, install the cable clamp, and tighten the two fixing screws (BT2x5) using an H1.5 Allen wrench.
![]() |
![]() |

- Pass the heatbed cable through the cable cover on the power supply protection cover, route the ground wire through the column, and use an H2.0 Allen wrench to fasten the ground wire to the column with an STW3.5×6 screw.
![]() |
![]() |
![]() |
![]() |
- Insert the heatbed temperature cable into the MC board.

- Insert the heatbed power cables into the corresponding connectors on the AC board in sequence;
⚠️ Note: There are two versions of the P2S heatbed. The Version 1 heatbed requires 3 power cables (red, blue, and gray) to be connected; the Version 2 heatbed requires 2 power cables (red and gray) to be connected.
![]() |
![]() |
|
Version 1: 3 cables (red, blue, gray)
|
Version 2: 2 cables (red, gray)
|
- Clip the cables into the cable trough, install the cable clamp on the AC board cover, and use an H1.5 Allen key to tighten the two securing screws (BT2x5).

Passo 2: Install the Purge Chute
Align the purge chute with the screw holes on the printer and tighten the four fixing screws in sequence using an H1.5 Allen key.
Passo 3: Install the Left Side Panel
You can refer to this wiki to reinstall the left side panel: Replacing the Left Side Panel.
Passo 4: Install the Rear Panel
You can refer to this wiki to reinstall the rear panel: Replacing the Rear Panel.
Passo 5:Tighten the heatbed screws
- Click “Home” on the screen, preheat the bed to 55°C, and maintain it for 5 minutes;



- Use an H2.0 Allen Key to tighten the four front screws (numbered 4–7)

Passo 6:Manually level the heatbed
After waiting for the heatbed temperature to drop to room temperature, you can refer to this Wiki to manually level the heatbed: P2S Bed Tramming.
Verifying Functionality
Connect the power supply, turn on the printer, and check whether the heatbed heats up normally or whether the displayed temperature is normal.
Notas Finais
We hope this guide has provided clear and practical support.
If the issue remains unresolved, please submit a support ticket and include your recent printer logs and additional pictures or other details. Our technical team will review your request and provide detailed assistance.
You can also visit Bambu AI, which can instantly answer common questions and provide you with operational guidance.











