XY Motor

The XY motors are stepper motors mounted at the back of the printer, responsible for moving the toolhead in the XY plane. There is one on each side, labeled A motor and B motor for identification.

38-ab-motor.png

Below is what the motor looks like when separate from the printer.

fac173.jpg

When to Use This Guide

  • Motor burnout
  • Bambu Lab Support confirmed XY motor failure through log analysis

After replacing one or both XY motors, the XY belts need to be tensioned. Refer to XY Belt Tensioning for detailed instructions.

Required Tools and Materials

  • New XY motor;
  • H2.0 hex wrench
  • H1.5 hex wrench (required only when replacing the B motor)
  • Tweezers

Aviso de Segurança

IMPORTANT!

Always power off and disconnect power on the printer before performing maintenance work. Not doing so means there is a risk of electric shock, short circuit, and damage to the printer or surrounding area.

When a maintenance task necessitates the printer being powered on, use insulated gloves for safety and pay special care not to pinch, damage, or put pressure on any exposed wires, connectors, or circuit boards. Additionally, the nozzle can be extremely hot so never touch it with exposed skin.

If you have any questions or concerns related to the above or the steps in this guide, please open a new ticket in our Support Page for assistance.

Replacement of the A Motor

Removing the A Motor

Passo 1: Remove the Rear Panel

Refer to the corresponding Wiki for your printer model to remove the rear panel:

rear_panel_screws_010.png 背板螺丝.jpg
P2S X2D

Passo 2: Remove the Waste Chute

Use a 1.5 mm hex wrench to remove the four screws securing the waste chute, then detach the chute from the printer.

excess_purge_026.png

Passo 3: Release the A Motor Cable

Disconnect the A motor cable from the MC board, then from right to left, release the cable from the clips and tape.

01_001.png

02_002.png

Peel off the tape from the cable to separate the motor cable.

03_003.png

Passo 4: Release the XY Belt Tensioner

Remove the XY belt tensioner on the A motor side. Using an H2.0 hex wrench, remove the four screws shown below to loosen the tensioner.
Note: Hold the tensioner bracket by hand while loosening the screws to prevent it from springing open.

04_004.png

05_005.png

06_006.png

Passo 5: Remove the A Motor

The A motor is secured by four screws. Two screws are visible, and the other two must be accessed from above using a long H2.0 hex screwdriver.
Use an H2.0 hex wrench to remove all four screws.
Note: Support the motor with your hand when removing the last screw to prevent it from falling.

09_009.png

Remove the belt from the motor pulley, take out the A motor, and pull the motor cable through the small opening to fully remove the motor.

10_010.png

11_011.png

Installing the A Motor

Passo 1: Install the A Motor

Thread the A motor cable through the cable hole, support the motor by hand, and place the belt onto the motor pulley.

11_011.png

12_012.png

Use an H2.0 hex wrench to secure the four motor screws. For the two screws at the back, insert the wrench from above, use tweezers to position the screws in the holes, and then tighten them.

09_009.png

13_013.png

Passo 2: Install the XY Belt Tensioner

Reinstall the XY belt tensioner and use an H2.0 hex wrench to tighten the tensioner bracket screws and the tensioning screw.

Note: Hold the tensioner by hand while tightening to prevent it from springing out.

07_007.png

Do not fully tighten the tensioning screw yet; it should be tightened after the belt is tensioned.

08_008.png

Passo 3: Connect the A Motor Cable

Tape the motor cable together with the other two cables, then from left to right, clip the cables into the cable clips and secure them to the frame with tape (at position 4).

03_003.png

02_002.png

Finally, connect the motor cable to the MC board.

01_001.png

Passo 4: Install the Waste Chute

Align the waste chute with the screw holes on the printer and use an H1.5 hex wrench to tighten the four mounting screws.

excess_purge_026.png

Passo 5: Install the Rear Panel

Refer to the corresponding Wiki for your printer model to install the rear panel:

rear_panel_screws_010.png 背板螺丝.jpg
P2S X2D

Replacement of the B motor

Removing the B Motor

Passo 1: Remove the Rear Panel

Refer to the corresponding Wiki for your printer model to remove the rear panel:

rear_panel_screws_010.png 背板螺丝.jpg
P2S X2D

Passo 2: Remove the AP Cover

You can refer to this wiki to remove the AP cover: Replace the P2S AP Board Cover/LED Light – Left

Passo 3: Remove the Waste Chute

Use an H1.5 hex wrench to remove the four screws securing the waste chute, then detach it from the printer.

excess_purge_026.png

Passo 4: Release the XY Belt Tensioner

Remove the XY belt tensioner on the B motor side. First, use an H2.0 hex wrench to remove the two tensioner mounting screws, then remove the tensioner bracket screws with the same wrench.
Note: Hold the tensioner bracket by hand while removing the screws to prevent it from springing open.

15_015.png

16_016.png

Loosen the tensioner bracket, then remove it from the printer.

17_017.png

18_018.png

Finally, slide the tensioner out of the frame and hang it on the belt.

19_019.png

Passo 5: Remove the MC Board

Refer to the corresponding Wiki for your printer model to remove the MC Board:

When removing the MC board, you can also release the B motor cable from the cable clips inside the printer.

37_037.png

Passo 6: Remove the B Motor

First, use an H2.0 hex wrench to remove the three screws securing the motor mount.

20_020.png

The B motor is secured by four screws — two are visible, and the other two must be accessed from above using a long H2.0 hex screwdriver. First, use the H2.0 hex wrench to loosen the two rear screws, then use tweezers to remove them.

21_021.png

22_022.png

23_023.png

Then use an H2.0 hex wrench to remove the two front screws. Support the motor by hand when removing the last screw to prevent it from falling.

24_024.png

14_014.png

Remove the belt from the B motor pulley and pull the motor cable out of the cable channel.

25_025.png

26_026.png

Push the motor downward. Since the bottom of the motor is blocked by a crossbeam, slide the mount inward and tilt the B motor to push it down past the crossbeam.

27_027.png

28_028.png

Installing the B Motor

Passo 1: Install the B Motor

Thread the motor cable from bottom to top through the main cable channel, then route it through the small channel on the left side.

31_031.png

Route the motor cable toward the right side panel, as shown in the figure. Push the mount inward to create space for the motor, then pass the motor from bottom to top through the small hole in the mount.

32_032.png

33_033.png

Loop the belt over the motor pulley, support the motor by hand, and tighten the two front mounting screws with an H2.0 hex wrench.

34_034.png

35_035.png

24_024.png

Insert the H2.0 hex wrench through the frame above the screw hole, use tweezers to place the screw into the hole, then tighten it. Use the same method for the two rear screws.

22_022.png

21_021.png

23_023.png

Use an H2.0 hex wrench to tighten the three mount screws.

20_020.png

Passo 2: Install the MC Board

Refer to the corresponding Wiki for your printer model to remove the MC Board:

When installing the MC board, clip the motor cables into the internal cable clips and connect them to the MC board.

37_037.png

Passo 3: Install the XY Belt Tensioner

Reinstall the XY belt tensioner and use an H2.0 hex wrench to tighten the bracket screws and the tensioning screw.
Note: Do not fully tighten the tensioning screw yet; it should be tightened after the belt is tensioned.

18_018.png

16_016.png

Hold the tensioner by hand while tightening the screws to prevent it from springing out.

15_015.png

Passo 4: Install the Waste Chute

Align the waste chute with the screw holes on the printer and use an H1.5 hex wrench to tighten the four mounting screws.

excess_purge_026.png

Passo 5: Install the Printer Rear Panel

Refer to the corresponding Wiki for your printer model to install the rear panel:

rear_panel_screws_010.png 背板螺丝.jpg
P2S X2D

Passo 6: Install the AP Cover

Refer to this wiki to reinstall the AP cover: Replace the P2S AP cover/LED Light – Left

Verifying Success

Connect the power, start the printer, and run the machine calibration to check for errors.

Notas Finais

We hope this guide has provided clear and practical support.
If the issue remains unresolved, please submit a support ticket and include your recent printer logs and additional pictures or other details. Our technical team will review your request and provide detailed assistance.
You can also visit Bambu AI, which can instantly answer common questions and provide you with operational guidance.