Replace the X2D Filament Cutter Assembly

🔎 Find the X2D Left Filament Cutter and X2D Right Filament Cutter in the Bambu Lab store.

The filament cutter assembly is the component used to cut old filament inside the toolhead when the printer switches filaments.
The X2D contains two filament cutter assemblies, namely the left and right filament cutter assemblies.
fac203.pngfac204.png

Applicable printer model

Bambu Lab X2D

When to Replace

If filament is not cut cleanly during unloading and inspection reveals wear on the filament cutter blade, replacement of the filament cutter assembly is recommended.

Required tools and materials

  1. New Filament Cutter Assembly
  2. H1.5 allen key
  3. Tweezers or Needle-Nose Pliers

Aviso de Segurança

⚠️ IMPORTANT!

It’s crucial to power off the printer before conducting any maintenance work, including work on the printer’s electronics and tool head wires. Performing tasks with the printer on can result in a short circuit, leading to electronic damage and safety hazards.

During maintenance or troubleshooting, you may need to disassemble parts, including the hotend. This exposes wires and electrical components that could short circuit if they contact each other, other metal, or electronic components while the printer is still on. This can result in damage to the printer’s electronics and additional issues.

Therefore, it’s crucial to turn off the printer and disconnect it from the power source before conducting any maintenance. This prevents short circuits or damage to the printer’s electronics, ensuring safe and effective maintenance. For any concerns or questions about following this guide, we recommend submitting a chamado técnico relatando o seu problema. and we will do our best to respond promptly and provide the assistance you need.

Video Guide

Replace the Left Filament Cutter Assembly

Passo 1. Remove the toolhead housing

Please refer to Toolhead Housing Replacement Guide for the X2D to remove the toolhead front cover and middle frame.

remove_toolhead_cover_002.png

Passo 2. Loosen the Left Filament Cutter Lever

Use an H1.5 allen key to remove the single screw of the left filament cutter lever, then rotate the filament cutter lever to expose the filament cutter lever component.

Passo 3. Remove the Left Filament Cutter Assembly

Use an H1.5 allen key to remove one screw, remove the filament pressure block, and use tweezers or needle-nose pliers to take out the left filament cutter assembly.

remove_left_screw_cutter_001.png

Passo 4. Install the New Left Filament Cutter Assembly

  • Refer to the illustration below to nest the left filament cutter assembly in the correct position. When installing, ensure the side of the filament cutter with the groove faces the front door of the printer.

    install_left_filament_cutter_003.png

  • Insert the filament pressure block and use an H1.5 allen key to tighten one fixing screw.

    install_left_filament_cutter_block_001.png

Passo 5. Install the Left Filament Cutter Lever

Insert the filament cutter lever component into the filament cutter lever, align and snap the central round hole into the threaded hole, then use an H1.5 allen key to tighten one fixing screw.

remove_filament_cutter_lever_001.png

Passo 6. Install the toolhead cover

Please refer to Toolhead Housing Replacement Guide for the X2D to install the toolhead front cover and middle frame.

install_toolhead_cover_001.png

Replace the Right Filament Cutter Assembly

Passo 1. Remove the toolhead housing

Please refer to Toolhead Housing Replacement Guide for the X2D to remove the toolhead front cover and middle frame.

remove_toolhead_cover_002.png

Passo 2. Loosen the Right Filament Cutter Lever

Push the nozzle assembly to the right to raise the right auxiliary hotend, then use an H1.5 allen key to remove the single screw of the right filament cutter lever to separate the lever from the filament cutter assembly. Rotate the filament cutter lever to expose the filament cutter lever component.

Passo 3. Remove the Right Filament Cutter Assembly

Push the filament cutter lever towards the X-Axis side to expose the fixing screw, then use an H1.5 allen key to remove one screw, and use tweezers or needle-nose pliers to remove the right filament cutter assembly.

remove_right_screw_filament_cutter_002.png

Passo 4. Install the New Right Filament Cutter Assembly

  • Refer to the illustration below to nest the right filament cutter assembly in the correct position. When installing, ensure the side of the filament cutter with the groove faces the front door of the printer.
    install_right_filament_cutter_003.png
  • Use an H1.5 allen key to tighten one fixing screw.
    install_right_filament_cutter_screw_001.png

Passo 5. Install the Right Filament Cutter Lever

Insert the filament cutter lever component into the filament cutter lever, align and snap the central round hole into the threaded hole, then use an H1.5 allen key to tighten one fixing screw.

install_right_filament_cutter_lever_001.png

Passo 6. Install the toolhead cover

Please refer to Toolhead Housing Replacement Guide for the X2D to install the toolhead front cover and middle frame.

install_toolhead_cover_001.png

Verifying Success

✅ The filament cutter operates smoothly and can cut filament properly.

Notas Finais

We hope this guide has provided clear and practical support.
If the issue remains unresolved, please submit a support ticket and include your recent printer logs and additional pictures or other details. Our technical team will review your request and provide detailed assistance.
You can also visit Bambu AI, which can instantly answer common questions and provide you with operational guidance.